QNAP NAS Community Forum

Hi,

I'm planning to buy a TS-212. I want to set up 2x2TB disks in RAID1 mode.
In the QNAP Comparison Chart the TS-212 does not have a function called "RAID Recovery", but it is not explained, what this function is. What I want to know is:
If one disk fails, is it possible to replace that disk and that afterwards the RAID1 will be rebuilt? What is this dubios feature called "RAID Recovery"?

Thanks
Mana

Hi Mana,
RAID Recovery is a QNAP exclusive and unique feature for RAID data protection during accidental disk removal or SATA connector failure.

http://docs.qnap.com/nas/en/index.html? ... gement.htm
"When the NAS is configured as RAID 5 (or RAID 6, 10) and any number of hard drives is uplugged from the server accidentally, you can plug in the same hard drives into the same drive slots and click ‘Recover’ to recover the volume status from ‘Not active’ to ‘Degraded mode’."

RAID from other competitors will crash and cause data loss if you unplug more than the allowed disk numbers in RAID.

RAID Recovery is available for QNAP NAS models with HDD hot-swap function.

TS-212 can still perform RAID rebuild if 1 HDD failed in the RAID 1 setup. You just nee to turn off TS-212, and then replace the failed HDD, and then power on the NAS for automatic RAID rebuild.

Jason

Hi Jason,

thanks for your answer, that's exactly what I wanted to know!!!
I just ordered the TS-212, so I hope I'll have it by the end of the week.

Thank you!
Mana

Dear Jason,

I just read your article about the QNAP TS-212. I have the problem that one of my hard discs failed. I changed the defect hard disc but I cannot recover the RAID 1? I have no options regarding the new disk. See Screenshot. Can you please help me!

Can you please explain me why and how this should work?

Best Regards
Stephan

QNAPJason wrote:Hi Mana,
RAID Recovery is a QNAP exclusive and unique feature for RAID data protection during accidental disk removal or SATA connector failure.

http://docs.qnap.com/nas/en/index.html? ... gement.htm
"When the NAS is configured as RAID 5 (or RAID 6, 10) and any number of hard drives is uplugged from the server accidentally, you can plug in the same hard drives into the same drive slots and click ‘Recover’ to recover the volume status from ‘Not active’ to ‘Degraded mode’."

RAID from other competitors will crash and cause data loss if you unplug more than the allowed disk numbers in RAID.

RAID Recovery is available for QNAP NAS models with HDD hot-swap function.

TS-212 can still perform RAID rebuild if 1 HDD failed in the RAID 1 setup. You just nee to turn off TS-212, and then replace the failed HDD, and then power on the NAS for automatic RAID rebuild.

Jason

I never realized QNAP had this advantage over the other competitors. Naice

After a long search I found an entry in the QNAP FAQ. As the TS-210 is very similar to the TS-212 this NAS does NOT support any RAID recovery! This is really stupid, because I thought this is the big advantage of QNAP. I have to sell the QNAP TS-212 and I am very disappointed about this issue Spend my money for nothing!

-----------------------------------------------------------------------
How can I migrate from Single Disk to RAID 0/1 in TS-210?
Applied Models:

TS-210 Turbo NAS
Answer:
TS-210 does not support Online RAID Level Migration. Therefore, please backup the data on the single disk to another location, install the second hard drive, and then recreate the new RAID 0/1 array (hard drive must be formatted).

2010/03/02
Question ID:693
For more technical support, please contact us.

(Found at http://www.qnap.com/de/faq_detail.asp?faq_id=693)

bosk wrote:After a long search I found an entry in the QNAP FAQ. As the TS-210 is very similar to the TS-212 this NAS does NOT support any RAID recovery!

RAID recovery, as described by QnapJason, is only applicable when using RAID 5, 6 or 10 so not an option on any two-disk unit.

How can I migrate from Single Disk to RAID 0/1 in TS-210?

The lack of Online RAID Migration feature is a limitation of the low-end models TS-210/212 that is clearly communicated in the marketing material. That feature is not the same as recovery of a degraded RAID 1. The latter is supported on all models that have RAID 1.

I don't know why your RAID 1 didn't recover as it should have done. I recommend you to contact Qnap support to get help with that issue.
'

is raid recovery as reliable as zfs for recovering back the raid ??

Hi P3R,

Thanks for your post and your comments!

I understood that the low-end models of QNAP do not have online raid migration or online raid enhancement. Also that there is no RAID5 supported. I am fine with that issue.

But as you mentioned it would be nice to have a recovery of a degraded RAID 1 for the TS-212. I already got in contact with the support but up to now I do not have an solution

Regs

Hi P3R and bosk,
RAID recovery is also available on the hot-swap supported NAS (e.g. TS-259 Pro +, TS-239 Pro II+).
It will recover the RAID back to degraded mode, and then the RAID will rebuild automatically from the degraded mode to the normal mode.

Jason

Hi Jason,

Okay I didn't know that and to tell you the truth I didn't look up the details about RAID Recovery but only extrapolated on the information you've already given. The message I concentrated on was to explain to bosk that despite the lack of RAID recovery on the TS-212, it should be able to rebuild the broken RAID 1 when a new disk was inserted. Hopefully he will get assistance with that problem so that he doesn't loose faith in his Qnap.

As posted in another post, I do not know why the RAID Rebuild did not started.

http://forum.qnap.com/viewtopic.php?f=2 ... 04#p199604

This works (I hope): http://inglele.wordpress.com/2012/07/19 ... om-telnet/
However I used SSH not telnet. I think it will work. It is rebuilding at the moment.