TS-212P status light red/green - HDD not detected
Posted: Mon Nov 07, 2011 5:33 am
Hey everyone,
I noticed last night that the status light was flashing red, I went in to volume management and saw that DIsk 1 had a bad disk error highlighted in red. I did a scan on it and it was fine. I did a search on the forum but everything i tried was with no luck. I have restarted the NAS and have made sure that the hard drives are connected.
I restarted the NAS this morning and both HDDs were fine and the the raid was rebuilding (RAID 1) - all of a sudden the status light was flashing green and red and when I went into disk management I could no longer see the disks. Since then none of my shares work.
I have only had this NAS for 3 weeks so its very weird to have this problem.
I am running the latest firmware (3.5.1) and it is a TS-212P.
After I restart the NAS, it then can locate both disks and says they are in good condition however when the raid starts to rebuild it stops after 3 percent. I check the system logs and see this:
2011-11-06 13:44:17 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] Error occurred while accessing Drive 2.
2011-11-06 13:07:33 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] Start rebuilding.
2011-11-06 13:06:24 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] The file system is not clean. It is suggested that you run "check disk".
2011-11-06 13:06:10 System 127.0.0.1 localhost System started.
2011-11-06 12:51:45 System 127.0.0.1 localhost System was shut down on Sun Nov 6 12:51:45 EST 2011.
I try to shutdown the NAS box via the web browser and it doesn't turn off. It is funny how it was saying drive 1 was faulty before and now drive 2. Could this be a firmware issue?
Can anyone please advice me on what the next steps should be?
Thank you
James
I noticed last night that the status light was flashing red, I went in to volume management and saw that DIsk 1 had a bad disk error highlighted in red. I did a scan on it and it was fine. I did a search on the forum but everything i tried was with no luck. I have restarted the NAS and have made sure that the hard drives are connected.
I restarted the NAS this morning and both HDDs were fine and the the raid was rebuilding (RAID 1) - all of a sudden the status light was flashing green and red and when I went into disk management I could no longer see the disks. Since then none of my shares work.
I have only had this NAS for 3 weeks so its very weird to have this problem.
I am running the latest firmware (3.5.1) and it is a TS-212P.
After I restart the NAS, it then can locate both disks and says they are in good condition however when the raid starts to rebuild it stops after 3 percent. I check the system logs and see this:
2011-11-06 13:44:17 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] Error occurred while accessing Drive 2.
2011-11-06 13:07:33 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] Start rebuilding.
2011-11-06 13:06:24 System 127.0.0.1 localhost [Mirror Disk Volume: Drive 1 2] The file system is not clean. It is suggested that you run "check disk".
2011-11-06 13:06:10 System 127.0.0.1 localhost System started.
2011-11-06 12:51:45 System 127.0.0.1 localhost System was shut down on Sun Nov 6 12:51:45 EST 2011.
I try to shutdown the NAS box via the web browser and it doesn't turn off. It is funny how it was saying drive 1 was faulty before and now drive 2. Could this be a firmware issue?
Can anyone please advice me on what the next steps should be?
Thank you
James