TS-251 No Signal on Newer TVs
-
- New here
- Posts: 8
- Joined: Sat Jul 30, 2011 11:09 pm
Re: TS-251 No Signal on Newer TVs
I have 2 * 4 GB Kingston SO-DIMM and the problem is here. How can we update to the beta hd station;
- schumaku
- Guru
- Posts: 43578
- Joined: Mon Jan 21, 2008 4:41 pm
- Location: Kloten (Zurich), Switzerland -- Skype: schumaku
- Contact:
Re: TS-251 No Signal on Newer TVs
This might be more on the subject here - not the special case @jimmgc51.sanad19 wrote:I have 2 * 4 GB Kingston SO-DIMM and the problem is here.
Lack of any information of the firmware and HD Station on place ... there is a QTS 4.2.1 Beta available for your NAS / this might or might not bring a new HD Station version *HD Station v3.1.0" here.sanad19 wrote:How can we update to the beta hd station;
-
- Starting out
- Posts: 10
- Joined: Sat Feb 07, 2015 1:41 am
Re: TS-251 No Signal on Newer TVs
Anyone can post an URL to download hdstation unoficial versión?
-
- Starting out
- Posts: 12
- Joined: Sun Oct 25, 2015 1:48 am
- Location: U.S.A.
Re: TS-251 No Signal on Newer TVs
I suppose I could post a link...the worst that will happen is QNAP will remove my link. I am not responsible for anything this version does to your unit. This is what QNAP support installed and my unit is working fine (for the most part). There are a few other very minor issues, that weren't there before, but I am happy with this test version. I wasn't here to monitor what they were doing, so I can't be certain if they performed a few other maintenance tasks to get it to work.
USE AT YOUR OWN RISK:
HD Station 3.1.2 (20160105) - UNOFFICIAL
https://drive.google.com/folderview?id= ... sp=sharing
Also, the memory that I have installed is 1x8GB of Crucial Technology Memory.
Edit: If you install this, be sure to update to the official version once it is released.
USE AT YOUR OWN RISK:
HD Station 3.1.2 (20160105) - UNOFFICIAL
https://drive.google.com/folderview?id= ... sp=sharing
Also, the memory that I have installed is 1x8GB of Crucial Technology Memory.
Edit: If you install this, be sure to update to the official version once it is released.
TS-251
Firmware: 4.3.2.0026
8GB Memory (single slot)
2x4TB WD Red NAS drives
Firmware: 4.3.2.0026
8GB Memory (single slot)
2x4TB WD Red NAS drives
-
- New here
- Posts: 8
- Joined: Sat Jul 30, 2011 11:09 pm
Re: TS-251 No Signal on Newer TVs
Worked!!!
-
- Starting out
- Posts: 10
- Joined: Sat Feb 07, 2015 1:41 am
Re: TS-251 No Signal on Newer TVs
Thank you very much
I'll try this 384mb little rabbit!!
I'll try this 384mb little rabbit!!
-
- Starting out
- Posts: 12
- Joined: Sun Oct 25, 2015 1:48 am
- Location: U.S.A.
Re: TS-251 No Signal on Newer TVs
Sanad, awesome news!
Betsunin, be sure to update so we know if it worked for you.
Betsunin, be sure to update so we know if it worked for you.
TS-251
Firmware: 4.3.2.0026
8GB Memory (single slot)
2x4TB WD Red NAS drives
Firmware: 4.3.2.0026
8GB Memory (single slot)
2x4TB WD Red NAS drives
-
- Starting out
- Posts: 10
- Joined: Sat Feb 07, 2015 1:41 am
Re: TS-251 No Signal on Newer TVs
Hi again
And....
... IT WORKED!!!!!
Tank you so much MegaCab
I was almost sure to sell my Qnap.
I'll give it a new chance.
Next Steps installing Aeon Nox Again into KODI, and setting all settings as in past.
(BTW with skin do u use for KODI?)
Thanks again.
And....
... IT WORKED!!!!!
Tank you so much MegaCab
I was almost sure to sell my Qnap.
I'll give it a new chance.
Next Steps installing Aeon Nox Again into KODI, and setting all settings as in past.
(BTW with skin do u use for KODI?)
Thanks again.
-
- Starting out
- Posts: 12
- Joined: Tue Dec 01, 2015 6:42 am
Re: TS-251 No Signal on Newer TVs
6.7LMegaCab wrote:Also, the memory that I have installed is 1x8GB of Crucial Technology Memory.
Could you please advise the model number of this RAM please?
I'll just buy this one and pop it in..
Thanks
-
- Starting out
- Posts: 10
- Joined: Sat Feb 07, 2015 1:41 am
Re: TS-251 No Signal on Newer TVs
I use an HS-251 and RAM is solded
-
- Starting out
- Posts: 12
- Joined: Tue Dec 01, 2015 6:42 am
Re: TS-251 No Signal on Newer TVs
So I have now purchased Crucial 1 x 8GB of RAM and the problem is the same, upon installation the HDMI port will not work. As soon as I re-install the 1GB it works fine.
This is a little annoying for using Kodi I really need the RAM upgraded, 1GB just doesn't cut it..
Can anyone advise what the problem may be or do I just have a dodgy NAS which should be returned?
This is a little annoying for using Kodi I really need the RAM upgraded, 1GB just doesn't cut it..
Can anyone advise what the problem may be or do I just have a dodgy NAS which should be returned?
-
- New here
- Posts: 2
- Joined: Mon May 09, 2016 8:41 am
Re: TS-251 No Signal on Newer TVs
Did you get any further with resolving your issue? I just bought a TS-251+ and am having the same issue. With the factory 2GB installed the HDMI works fine, but I bought 2x4GB Kingston sticks and with either or both of them in the HDMI doesn't work (though the NAS otherwise works fine).
-
- New here
- Posts: 2
- Joined: Mon May 09, 2016 8:41 am
Re: TS-251 No Signal on Newer TVs
Actually I just got mine working with the Kingston RAM by replacing the HDMI cable. Doesn't really make sense but that did it
-
- Starting out
- Posts: 42
- Joined: Wed Jan 18, 2012 11:33 pm
Re: TS-251 No Signal on Newer TVs
Opened a ticket yesterday...the told me to read this post....
Quite strange, since no solution here.
Quite strange, since no solution here.
---------------------------------------
My blog https://www.iu5hes.com
---------------------------------------
My blog https://www.iu5hes.com
---------------------------------------
-
- Starting out
- Posts: 21
- Joined: Sat Oct 17, 2015 2:53 am
Re: TS-251 No Signal on Newer TVs
I've same problem with my TS-251. It has always worked fine, till about a week ago, maybe when I upgraded to QTS 4.3.3
It works fine till HD Station has loaded, then I have to restart it everytime I turn off TV (or simply I change the input).
If I restart nas, I can turn off and on the tv or change the input, until HD Station is loaded.
I have QTS 4.3.3 and HD Station 3.1.A
2x4GB HyperX always worked correctly (from October 2015).
It works fine till HD Station has loaded, then I have to restart it everytime I turn off TV (or simply I change the input).
If I restart nas, I can turn off and on the tv or change the input, until HD Station is loaded.
I have QTS 4.3.3 and HD Station 3.1.A
2x4GB HyperX always worked correctly (from October 2015).