Just hit the same issue on brand new TS-664
Hard reset and factory reset did not do the tirck
Any Suggestions - went through the posts on forum and have not find any solution.
RAID Re-sync constant since FW upgrade
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
- dolbyman
- Guru
- Posts: 35272
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: RAID Re-sync constant since FW upgrade
Please do not necropost, old topic locked and split
viewtopic.php?f=25&t=157697
Please explain current firmware used and issue at hand (doubt you have a 3 year old firmware running)
viewtopic.php?f=25&t=157697
Please explain current firmware used and issue at hand (doubt you have a 3 year old firmware running)
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
Re: RAID Re-sync constant since FW upgrade
Setup:
1. Brand new TS-664
2. QTS QTS 5.0.1.2248 build 20221215 - it seems to be a build form 15th Dec 2022 as build is in YYYY-MM-DD format do can not be 3Y old ;(
3. RAID 5 on 3x 12 TB (usable 10.91 TB) Seagate ST12000VN0008-2YS101
4. 1 storage pool of the max size for RAID 5 that is 21,8 TB with guaranteed snapshot pool
5. 1 Thin volume
6. RAID Scrubbing Off
Issue:
every time I reboot / shutdown / power up the
RAID Group (whole 21 TB) starts synchronizing despite the fact it was already synchronized before power down- power down is done from QTS
My understanding is that unoccupied space of the Storage Pool that is not a part of any data Volume should not be synchronized - am I wrong?
I'd like not to have to sync whole pool upon each boot as it takes time (10+h actually if set to max performance for sync).
1. Brand new TS-664
2. QTS QTS 5.0.1.2248 build 20221215 - it seems to be a build form 15th Dec 2022 as build is in YYYY-MM-DD format do can not be 3Y old ;(
3. RAID 5 on 3x 12 TB (usable 10.91 TB) Seagate ST12000VN0008-2YS101
4. 1 storage pool of the max size for RAID 5 that is 21,8 TB with guaranteed snapshot pool
5. 1 Thin volume
6. RAID Scrubbing Off
Issue:
every time I reboot / shutdown / power up the
RAID Group (whole 21 TB) starts synchronizing despite the fact it was already synchronized before power down- power down is done from QTS
My understanding is that unoccupied space of the Storage Pool that is not a part of any data Volume should not be synchronized - am I wrong?
I'd like not to have to sync whole pool upon each boot as it takes time (10+h actually if set to max performance for sync).
Regards
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
- dolbyman
- Guru
- Posts: 35272
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: RAID Re-sync constant since FW upgrade
What apps/services are installed? (ISCSI?) Normally a re-sync only happens when the volume could not be unmounted successfully and get's yanked offline (powerloss or an app/service that holds it hostage during reboot)
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
Re: RAID Re-sync constant since FW upgrade
no ISCSI
Installed standard QTS APPS like:
Helpdesk, licence Center, Network & Virtual Switch, Notification Center, QTS SSL Cett, QuLogCenter, Resource monitor.
so nothing special..
Yes I do agree something prevents NAS from proper shutdown, but from UI it looks like is is being properly shutdown.
Installed standard QTS APPS like:
Helpdesk, licence Center, Network & Virtual Switch, Notification Center, QTS SSL Cett, QuLogCenter, Resource monitor.
so nothing special..
Yes I do agree something prevents NAS from proper shutdown, but from UI it looks like is is being properly shutdown.
Regards
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
Re: RAID Re-sync constant since FW upgrade
Can UPS USB signal cable influence the shutdown as I have APC UPS connected via USB as to shutdown in case of power failure?
Wysłane z mojego SM-M215F przy użyciu Tapatalka
Wysłane z mojego SM-M215F przy użyciu Tapatalka
Regards
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
Re: RAID Re-sync constant since FW upgrade
The ticket is sitting with support for over 7 days and the only advice was to turn off disk usage statistics distribution to qnap.
Not to mention that they treat reboot as shutdown and start :facepalm: ...
the synchronization was not triggered after restart so we claim we have resolved the issue
while original case mentions : " [..] the NAS is constantly synchronizing the storage pool after each shutdown. [..]"
More updates to come...
Not to mention that they treat reboot as shutdown and start :facepalm: ...
the synchronization was not triggered after restart so we claim we have resolved the issue
while original case mentions : " [..] the NAS is constantly synchronizing the storage pool after each shutdown. [..]"
More updates to come...
Regards
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
-
- Getting the hang of things
- Posts: 50
- Joined: Sat Sep 10, 2016 1:16 pm
Re: RAID Re-sync constant since FW upgrade
I have TS-451+ with this same issue.
I notice this problem starting from upgrade firmware. ( But cannot remember which version cause this problem)
After reboot I start to sync immediatly.
If I reboot while it not finish sync, the volume will also have error "volumn no clean"
update: not found this problem after upgrade to QTS 5.0.1.2277
I notice this problem starting from upgrade firmware. ( But cannot remember which version cause this problem)
After reboot I start to sync immediatly.
If I reboot while it not finish sync, the volume will also have error "volumn no clean"
update: not found this problem after upgrade to QTS 5.0.1.2277
-
- New here
- Posts: 6
- Joined: Tue Jan 24, 2023 1:28 am
Re: RAID Re-sync constant since FW upgrade
Turn off automati send of the disks diagnostics to qnap.
Wait for sync complete.
Restart
Should be fine.
If this will not work retry.
Id this still dows not work reach support.
Wysłane z mojego SM-M215F przy użyciu Tapatalka
Wait for sync complete.
Restart
Should be fine.
If this will not work retry.
Id this still dows not work reach support.
Wysłane z mojego SM-M215F przy użyciu Tapatalka
Regards
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215
Rafał
___________________
TS-664 with 3 x Seagate ST12000VN0008-2YS101 12TB RAID 5
running on QTS 5.0.1.2248 build 20221215