I’m segmenting my home network into different subnets and setting up vLANS. For most part all makes sense; however I’m having trouble with the IP address of my switch, and I’m hoping someone might be able to help point me in the right direction.
I have a pfsense L3 router (Negate 6100) which is connected to an L2 switch (QNAP QSW-M408-4C). I’m sending 2 vLANS (#10 Primary & #30 Management) via a trunk from the LAN interface on the router, to a trunked port on the switch.
On the switch, I have 3 access ports configured for vLAN #10 and 2 access ports configured for vLAN #30. The devices connecting to access ports get assigned IP addresses from the respective subnet ranges via DHCP and all works well. however, the switch itself is getting a self-assigned IP address, leaving the management webUI unaccessible from the network.
Ideally I want the switch on the management vLAN (#30). My hope was that I could simply do a DHCP server static mapping, but that does not appear to work. Manually setting the IP address and DNS server of the switch doesn’t work either. It takes the address, but is still not accessible on the network, and does not appear on the router ARP table.
My firewall is currently set to allow everything across all interfaces whilst trying to resolve this, so I don't believe that is causing any issues.
Any ideas on how to get DHCP working for the switch itself when using a trunk from router to switch?
Thanks in advance for any help/advice.
QSW-M408-4C, vLANs and switch IP address
-
- First post
- Posts: 1
- Joined: Sun Jan 02, 2022 2:07 pm
QSW-M408-4C, vLANs and switch IP address
You do not have the required permissions to view the files attached to this post.
-
- First post
- Posts: 1
- Joined: Wed Oct 05, 2022 11:30 pm
Re: QSW-M408-4C, vLANs and switch IP address
Any solution to change vlan management?
- dolbyman
- Guru
- Posts: 35272
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: QSW-M408-4C, vLANs and switch IP address
Best to open a ticket with QNAP, doubt many people here use these switches, so you will wait in vain for any tips or answers
-
- First post
- Posts: 1
- Joined: Wed Oct 26, 2022 9:12 pm
Re: QSW-M408-4C, vLANs and switch IP address
At the risk of also being told to raise a ticket, any update on the VLAN ID 1 / management issue?
- dolbyman
- Guru
- Posts: 35272
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: QSW-M408-4C, vLANs and switch IP address
Looks like a hit and run poster. posted and never came back
-
- First post
- Posts: 1
- Joined: Fri Oct 28, 2022 4:29 pm
Re: QSW-M408-4C, vLANs and switch IP address
I have exactly the same switch and the same issue: I need to move the management vlan id to 100 (i.e. not 1). This is a deal breaker for me if I cannot figure this out. I will raise a ticket.
-
- First post
- Posts: 1
- Joined: Thu Dec 01, 2022 6:19 pm
Re: QSW-M408-4C, vLANs and switch IP address
I have a QSW-2108-2C and have a similar issue - not sure where to find PVIDs - the interface is overly simplstic and not consistent with other coommercial switches . . . very confusing indeed!
- dolbyman
- Guru
- Posts: 35272
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: QSW-M408-4C, vLANs and switch IP address
First post galore in here..see my first reply..OPEN TICKETS!