The resource monitor (Adapter section) of a TS-859 running 4.3.5.0713 only shows 4 of 6 physical NIC's. 1+2 are internal, 4+5 the first separate NIC (Intel 1gb dual port). 1+2 are grouped and 4+5, too. The 4 single ports and the 2 groups are displayed by the resource monitor.
But the second separate NIC (Intel 10gb dual port) doesn't. Traffic flows up to 600mb/s and I can see that under control panel/system resources. But this displays the overall network traffic and not separated by the NIC's.
Any idea how to tell this monitor to display every NIC?
How to configure resource monitor (Network IF)? Some IF won't show
-
- New here
- Posts: 6
- Joined: Tue Oct 09, 2018 1:49 am
-
- New here
- Posts: 6
- Joined: Tue Oct 09, 2018 1:49 am
Re: How to configure resource monitor (Network IF)? Some IF won't show
Probably my description is somehow unclear....here are two screenshots:
You do not have the required permissions to view the files attached to this post.
- storageman
- Ask me anything
- Posts: 5506
- Joined: Thu Sep 22, 2011 10:57 pm
Re: How to configure resource monitor (Network IF)? Some IF won't show
Have you tried using Service Binding to limit traffic to the 10GbE ports?
-
- New here
- Posts: 6
- Joined: Tue Oct 09, 2018 1:49 am
Re: How to configure resource monitor (Network IF)? Some IF won't show
Not yet....but no change after activating service binding. Even no change after installing 4.3.5-0722 firmware and a reboot. Strange....storageman wrote:Have you tried using Service Binding to limit traffic to the 10GbE ports?
- Trexx
- Ask me anything
- Posts: 5388
- Joined: Sat Oct 01, 2011 7:50 am
- Location: Minnesota
Re: How to configure resource monitor (Network IF)? Some IF won't show
You could try the following commands to reset NW stack (from another thread).
I would disable any 2nd port on your NW teams to prevent issues connecting.
I would disable Container Station & Virtual Station prior to running these and you likely would have to reinstall Virtual Station & Container Station after this.
Code: Select all
/mnt/ext/opt/netmgr/netmgr.sh reset_all_settings_to_default
/etc/init.d/network.sh reset_network_config_to_default
/etc/init.d/network.sh clean-restart
I would disable Container Station & Virtual Station prior to running these and you likely would have to reinstall Virtual Station & Container Station after this.
Paul
Model: TS-877-1600 FW: 4.5.3.x
QTS (SSD): [RAID-1] 2 x 1TB WD Blue m.2's
Data (HDD): [RAID-5] 6 x 3TB HGST DeskStar
VMs (SSD): [RAID-1] 2 x1TB SK Hynix Gold
Ext. (HDD): TR-004 [Raid-5] 4 x 4TB HGST Ultastor
RAM: Kingston HyperX Fury 64GB DDR4-2666
UPS: CP AVR1350
Model:TVS-673 32GB & TS-228a Offline[/color]
-----------------------------------------------------------------------------------------------------------------------------------------
2018 Plex NAS Compatibility Guide | QNAP Plex FAQ | Moogle's QNAP Faq
Model: TS-877-1600 FW: 4.5.3.x
QTS (SSD): [RAID-1] 2 x 1TB WD Blue m.2's
Data (HDD): [RAID-5] 6 x 3TB HGST DeskStar
VMs (SSD): [RAID-1] 2 x1TB SK Hynix Gold
Ext. (HDD): TR-004 [Raid-5] 4 x 4TB HGST Ultastor
RAM: Kingston HyperX Fury 64GB DDR4-2666
UPS: CP AVR1350
Model:TVS-673 32GB & TS-228a Offline[/color]
-----------------------------------------------------------------------------------------------------------------------------------------
2018 Plex NAS Compatibility Guide | QNAP Plex FAQ | Moogle's QNAP Faq
-
- New here
- Posts: 6
- Joined: Tue Oct 09, 2018 1:49 am
Re: How to configure resource monitor (Network IF)? Some IF won't show
Thanks for helping out. Actually I'm out of time and will try at the end of October and come back with the result.Trexx wrote:You could try the following commands to reset NW stack (from another thread)......