The police were called to a neighbouring property last night after an attempted break-in. As a result, I went to review my recordings to see if there was anything that could be useful to them to find that nothing has been recorded since the upgrade to QVR Pro 1.2.1.2 on 15/03/2019. Everything looks fine, but I no longer have motion events in my event log, and nothing is being recorded.
What I am getting now is twice a day alerts for all my disks; example - Surveillance Events - Disk [1] over [30000] hours, current used [38646] hours.
Has anyone else seen this and can anyone advise on a reason or resolution? Obviously keen to get the cameras actually recording again as soon as possible.
Should I downgrade to an earlier version?
[SOLVED] Recordings stopped following QVR Pro 1.2.1.2 install
-
- New here
- Posts: 3
- Joined: Tue Dec 31, 2013 7:58 pm
[SOLVED] Recordings stopped following QVR Pro 1.2.1.2 install
Last edited by GarryMartin on Mon Mar 25, 2019 11:20 pm, edited 1 time in total.
- storageman
- Ask me anything
- Posts: 5507
- Joined: Thu Sep 22, 2011 10:57 pm
Re: Recordings stopped following QVR Pro 1.2.1.2 install
QVR Pro basic only allows viewing up to 14 days via QVR GUI but recordings can still be viewed via the File Station folder after 14 days depending on settings and available space.
-
- New here
- Posts: 3
- Joined: Tue Dec 31, 2013 7:58 pm
Re: Recordings stopped following QVR Pro 1.2.1.2 install
Thanks. I am aware of the *playback* limitation but my issue is that it isn't recording.
Since the upgrade to 1.2.1.2 I no longer have any recordings. I do have recordings right up until the upgrade on the 15/03/2019 and can view those without issue at the moment. It's just not recording any longer, and there are no motion detected events in the logs.
Since the upgrade to 1.2.1.2 I no longer have any recordings. I do have recordings right up until the upgrade on the 15/03/2019 and can view those without issue at the moment. It's just not recording any longer, and there are no motion detected events in the logs.
-
- Know my way around
- Posts: 101
- Joined: Sun Jun 10, 2018 10:54 pm
Re: Recordings stopped following QVR Pro 1.2.1.2 install
Do you have recording set for 24/7 or only on a motion event? If you are only recording on motion detection, first check the obvious (that the event is "on"). If that isn't the issue, you could try to delete the event and create a new one. Just guessing, but maybe your event became corrupted in the upgrade process.
You could also try rebooting your camera and/or rebooting your system.
You could also try rebooting your camera and/or rebooting your system.
- storageman
- Ask me anything
- Posts: 5507
- Joined: Thu Sep 22, 2011 10:57 pm
Re: Recordings stopped following QVR Pro 1.2.1.2 install
Hmm, after any upgrades it's pretty important to check everything still works especially if primary function is cctv security.GarryMartin wrote: ↑Mon Mar 25, 2019 9:07 pm Thanks. I am aware of the *playback* limitation but my issue is that it isn't recording.
Since the upgrade to 1.2.1.2 I no longer have any recordings. I do have recordings right up until the upgrade on the 15/03/2019 and can view those without issue at the moment. It's just not recording any longer, and there are no motion detected events in the logs.
Qnap are good at breaking things...
-
- New here
- Posts: 3
- Joined: Tue Dec 31, 2013 7:58 pm
Re: Recordings stopped following QVR Pro 1.2.1.2 install
Recording was set for motion only.
Deleting and recreating the events worked. Thanks for the tip, but a little disconcerting that it is a required step and that there was no alert that recordings weren't being made. I'll have to look into that in more detail.
Deleting and recreating the events worked. Thanks for the tip, but a little disconcerting that it is a required step and that there was no alert that recordings weren't being made. I'll have to look into that in more detail.
-
- First post
- Posts: 1
- Joined: Wed May 15, 2019 10:17 am
Re: [SOLVED] Recordings stopped following QVR Pro 1.2.1.2 install
I have the exact same issue as the previous post.... but I have to re-add the events every reboot....anyone have a solution.?