Bosch Security Cameras writing to iSCSI QNAP

[jmerlos887]

Erro de Login.jpg

Hello team,

I new in this technology and my english is not good, I will try to explain myself in the best possible way.
Here we go...
I have the following scenario..

1 QNAP TS-131p // Firm: 4.3.6.0979
1 CAM Bosch NDN-50022-A3 // Firm: 6.23.0003
1 CAM Bosch NUC-51022-F2 // Firm: 6.23.0003

Configuration Manager v05.43.0238.0


The problem is, when I will try tu conect the Bosch camera with ISCSI in the QNAP, I received the error: the ISCSI device is password protected...

I think the correct password is the same I use to acces to QNAP system, i hope someone can give me some way to resolve this problem or maybe I made some wrong in the configurations

Regards in advance

Error Image:

[dolbyman]

don't think ISCSI is a good idea, you would need two LUN's for your two cameras and in order to access your footage the LUNs need to be unmounted from your cameras

no SMB/NFS/FTP option on those cams ?

[jmerlos887]

don't think ISCSI is a good idea, you would need two LUN's for your two cameras and in order to access your footage the LUNs need to be unmounted from your cameras

no SMB/NFS/FTP option on those cams ?

Thanks for the answer, this camera don´t have this protocols

But is not necessary create a Target ISCSI?

[dolbyman]

you have to create two targets for the cameras

might be better to go with a nvr system (qnap has qvr or surveilance station)

[jmerlos887]

the client request is use the qnap only to storage by LUNS, I don´t know if need to configure something else

[dolbyman]

got any screenshots of your ISCSI target config on the QNAP ?

[jmerlos887]

Let you some screenshots

ISCI Config


LUN Config


Storage Config

[dolbyman]

could you switch your interface to english and attach the photos here in the forum? they don't open right on mobile

[storageman]

don't think ISCSI is a good idea, you would need two LUN's for your two cameras and in order to access your footage the LUNs need to be unmounted from your cameras

no SMB/NFS/FTP option on those cams ?

Why two LUNs? Completely unnecessary. I don't think you understand ISCSI.
One PC/server presents a share say E:\ to cameras.

One LUN/formatted volume and two folders

Anyway none of this makes sense, so how will the cameras connect to the host, they have to support some file protocol.

[dolbyman]

no .. I do grasp iscsi block storage

the cameras (i quickly skimmed the manual) have an iscsi initiator interface in their config

but if two cameras access the same iscsi target ..would that reak havok on the target ?


the cameras apparently only support

sd recording
iscsi recording
onvif access

[storageman]

no .. I do grasp iscsi block storage

the cameras (i quickly skimmed the manual) have an iscsi initiator interface in their config

but if two cameras access the same iscsi target ..would that reak havok on the target ?


the cameras apparently only support

sd recording
iscsi recording
onvif access

Apologies! I am shamed!

Interesting, I never knew some cameras had ISCSI initiators!
Did Op format the LUN? I see format is not ticked.
Amazed anyone would try ISCSI on TS-131P!

[dolbyman]

thats ok ... I deep down knew you were joking (lets go with that )

don't know if op formatted the luns...op?

maybe there is a bosh software/hardware solution that can mount those iscsi lun safely to read them ? ..no idea

[storageman]

jmerlos887,

There should be no ISCSI password unless you set one via CHAP.
Can you connect to any other initiator? Windows PC say?

[jmerlos887]

jmerlos887,

There should be no ISCSI password unless you set one via CHAP.
Can you connect to any other initiator? Windows PC say?

Just yesterday I realized that detail, the conections is working on and cameras are recording in qnap

The problem was that.
I was putting a password but it was not necessary as you tell me

I thank you very much everybody

[storageman]

Cheers!

Dolbyman and I liked to get thanked!