Wattage used
-
- Know my way around
- Posts: 154
- Joined: Sat Aug 15, 2020 11:33 pm
Wattage used
Hi all, I have a TS-653D. Does anyone have a rough idea of how many watts this nas would use if it had 5 standard hardrives in it and 1 SSD? I'm looking for a UPS for this and I don't know how long the battery on it needs to last. Thanks
- howarmat
- Know my way around
- Posts: 222
- Joined: Tue Aug 21, 2012 12:30 am
Re: Wattage used
https://www.qnap.com/en-us/product/ts-6 ... s/hardware
specs there give you an idea but its not going to be too much.
specs there give you an idea but its not going to be too much.
-
- Know my way around
- Posts: 154
- Joined: Sat Aug 15, 2020 11:33 pm
Re: Wattage used
Cool thanks I didn't know they had that spec on their site. So I would imagine a router, switch and modem would each be less than that. What do you think?
- dolbyman
- Guru
- Posts: 36225
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: Wattage used
Hard to say without the model numbers..most manufacturers have the numbers on their websitee as well (and it's also written on the case of the device)
-
- Know my way around
- Posts: 154
- Joined: Sat Aug 15, 2020 11:33 pm
Re: Wattage used
I have the netgear R7200 router. Website specs don't say and neither does user manual. Oh well, I'm sure it's not more than a nas with 6 drives spinning.
- dolbyman
- Guru
- Posts: 36225
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: Wattage used
As said, volt/amp or watts should be on the sevice
-
- Know my way around
- Posts: 154
- Joined: Sat Aug 15, 2020 11:33 pm
Re: Wattage used
It's 12v/3.5a. I put that in a converter online and it said 42 watts. Si that would be the max?
- dolbyman
- Guru
- Posts: 36225
- Joined: Sat Feb 12, 2011 2:11 am
- Location: Vancouver BC , Canada
Re: Wattage used
Pretty much max yes..(a lot for a consumer router)
-
- Experience counts
- Posts: 2062
- Joined: Tue May 29, 2018 3:02 am
- Location: Everywhere I go, there I am.
Re: Wattage used
Max power ratings can vary wildly compared to actual usage. Particularly in a NAS, the only way to know how sure is to use a meter device.
Just an FYI, the "online converter" for watts (w) is simply voltage (v) multiplied by amperage (a).
12 * 3.5 = 42
The printed value on the power supply is the maximum it is designed to output.
Just an FYI, the "online converter" for watts (w) is simply voltage (v) multiplied by amperage (a).
12 * 3.5 = 42
The printed value on the power supply is the maximum it is designed to output.
QNAP TS-563-16G 5x10TB Seagate Ironwolf HDD Raid-5 NIC: 2x1GB 1x10GbE
QNAP TS-231P-US 2x18TB Seagate Exos HDD Raid-1
[Deadbolt and General Ransomware Detection, Prevention, Recovery & MORE]
QNAP TS-231P-US 2x18TB Seagate Exos HDD Raid-1
[Deadbolt and General Ransomware Detection, Prevention, Recovery & MORE]
-
- Know my way around
- Posts: 154
- Joined: Sat Aug 15, 2020 11:33 pm
Re: Wattage used
Thanks for your help. I'm going to get the CyberPower CP1350AVRLCD3 ups
- howarmat
- Know my way around
- Posts: 222
- Joined: Tue Aug 21, 2012 12:30 am
Re: Wattage used
Should be plenty as I have an 8 bay i5 NAS, 2 i7 PCs, a router and some other devices and normally well below 500 and only using 1/3 of capacity on my CP1500PFCLCDa
-
- Experience counts
- Posts: 2062
- Joined: Tue May 29, 2018 3:02 am
- Location: Everywhere I go, there I am.
Re: Wattage used
It all depends on how long you want to run on battery if there is a power failure
I use an APC1200 for my NAS, switch, HUE, 2xRasPI but I also use an identical unit just for my ISP router and internal router. I get about 20-30 minutes on the first one and at least 6 hours on the second.
QNAP TS-563-16G 5x10TB Seagate Ironwolf HDD Raid-5 NIC: 2x1GB 1x10GbE
QNAP TS-231P-US 2x18TB Seagate Exos HDD Raid-1
[Deadbolt and General Ransomware Detection, Prevention, Recovery & MORE]
QNAP TS-231P-US 2x18TB Seagate Exos HDD Raid-1
[Deadbolt and General Ransomware Detection, Prevention, Recovery & MORE]